Hand Crimp Tool for 2.50mm Board-In Crimp Terminals Application Tooling TYPE 4A Specification Sheet Modular Crimp Head Hand Crimp Tool Order No. 63823-7970 Order No. 63823-7900 FEATURES % A full cycle ratcheting hand tool ensures complete crimps % Ergonomically designed soft handles % Precisely designed crimping profiles with simple contact positioning % Easy handling due to outstanding force ratio % Modular Crimp Head is removable and can be use in the Air Powered Tool Order No.63816-0100, accompanied by Air Powered Crimp Adapter (Order No. 63816-0700). % Can also be used in the Battery Powered Tool Order No.63816-0200 (110 V) or 63816-0250 (220 V), accompanied by Battery Powered Crimp Adapter (Order No. 63816-0600). SCOPE Products: 2.50mm (.098") Board-In Crimp Terminal, 22-28 AWG, UL1007 and UL1569 wires. Terminal Terminal Order No. Wire Size (cid:2)Insulation Diameter Strip Length Series No. (cid:1)(cid:1)(cid:1)(cid:1) Reel AWG mm² mm In. mm In. 35047-9800 35047-9802 35047 22-28 0.33-0.08 1.15-1.90 .045-.075 2.40-2.90 .094-.114 35047-9810 (cid:2) Insulation crimp to meet IPC/WHMA-A-620 Class 2 compliance. Note: Terminal will accommodate the UL1007 and UL1569 wires. (cid:1) Customer to cut off terminal from reel: 0.30mm (.012”) maximum Cut-off Tab. DEFINITION OF TERMS BEND UP BELL MOUTH BRUSH INSULATION SEAM CRIMP ▲SEE NOTE ROLLING TWISTING STRIP BEND LENGTH DOWN CONDUCTOR CUT-OFF TAB CRIMP COND.CRIMP HEIGHT The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope. Doc No: ATS-6382379HM Release Date: 09-02-10 UNCONTROLLED COPY Page 1 of 7 Revision: B Revision Date: 10-14-10

Hand Crimp Tool for 2.50mm Board-In Crimp Terminals OVERLAP FORM GEOMETRY ▲Insulation Crimp Note: PUNCH Due to the terminal’s insulation grip design and/or insulation diameter range, this tool uses “overlap” form geometry in the insulation punch. This produces an overlap insulation crimp (A620 – compliant). While the OVERLAP insulation punch profile may appear “lopsided”, this is a INSULATION normal condition for this tool. See figure to the right. CRIMP (Some tools with multiple crimp pockets may not have the “overlap” profile on all pockets). CRIMP SPECIFICATIONS: WIRE ANVIL Bell mouth Conductor Brush Max. Terminal Series No. mm In. mm In. 35047 0.20-0.50 .008-.020 1.40 .055 Seam Bend up Bend down Twist Roll Terminal Series No. Degree Degree Seam shall not be open and no wire allowed out 35047 3 3 3 3 of the crimping area After crimping, the conductor profile should measure the following. Conductor Crimp Insulation Crimp Pull Force Terminal Wire Size Width Profile AWG Height Width Height (Ref) Minimum Series No. Maximum AWG mm2 mm In. mm In. mm In. mm In. N Lb. 22 24 26 28 22 0.33 0.82-0.87 .032-.034 1.30-1.50 .051-.059 1.70 Max .067 Max 1.90 .075 39.1 8.80 X 24 0.20 0.75-0.80 .029-.031 1.30-1.50 .051-.059 1.60 Max .063 Max 1.90 .075 29.3 6.60 X 35047 26 0.13 0.70-0.75 .027-.029 1.30-1.50 .051-.059 1.55 Max .061 Max 1.90 .075 19.6 4.40 X 28 0.08 0.66-0.71 .026-.028 1.30-1.50 .051-.059 1.50 Max .059 Max 1.90 .075 9.8 2.20 X • Tool Qualification Notes: 1. Pull Force should be measured with no influence from the insulation crimp. 2. The above specifications are guidelines to an SWING optimum crimp. HAND TOOL LOCATOR OPEN OPEN OPERATION Open the tool by squeezing the handles together, WIRE at the end of the closing stroke, the ratchet STOP BLADE mechanism will release the handles, and the hand tool will spring open. TERMINAL 1. With the hand tool in the open position, pivot SEATED IN the terminal locator open by pulling up on the LOCATOR Figure 1 locator knob and lift the wire stop blade up. See Figure 1. Doc No: ATS-6382379HM Release Date: 09-02-10 UNCONTROLLED COPY Page 2 of 7 Revision: B Revision Date: 10-14-10

Hand Crimp Tool for 2.50mm Board-In Crimp Terminals 2. Insert the terminal into the correct profile until the terminal is fully seated and stops. Make sure the wire stop blade is fully in up position. 3. Gently pivot the locator closed. 4. Bring down the wire stop blade. Make sure the wire stop blade is fully seated on the terminal behind the conductor grip section. 5. Slide the pre-stripped wire into the terminal; make sure to aim the wire brush towards the tip point on the wire stop blade. See Figure 2. Align the wire so that it is parallel and sitting into the terminal. Maintain a light and constant pressure on the wire that is seated in the terminal at all times. (Do not let go of the wire.) Be sure to hold the wire and terminal in place until the terminal is fully crimped. See Figure 3. WIRE STOP BLADE INSULATION WIRE STOP CONDUCTOR PUNCH TERMINAL PUNCH BLADE INSULATION LOCATOR PUNCH WIRE INSULATION CONDUCTOR TERMINAL ANVIL ANVIL WIRE Figure 2 Figure 3 6. Close the tool until the ratchet releases, the tool handles will then spring open. 7. Lift the wire stop blade up. 8. Carefully remove the crimped terminal. Pivot the terminal locator slightly out if necessary. See Figure 4. Note: The tamper proof ratchet action will not release the tool until it has been fully closed. Note: To maintain good brush control and a consistent bell mouth the crimping instructions must be followed. REMOVE CRIMPED WIRE Figure 4 CORRECT INCORRECT INCORRECT PIVOT LOCATOR Figure 5 Doc No: ATS-6382379HM Release Date: 09-02-10 UNCONTROLLED COPY Page 3 of 7 Revision: B Revision Date: 10-14-10

Hand Crimp Tool for 2.50mm Board-In Crimp Terminals Terminal Locator Replacement This section describes the procedure for changing locators. Removal 1. With the tool in the open position, pivot the terminal locator outward. 2. Remove the M4 BHCS. See Figure 6. Installation 1. Place the replacement locator on the hand tool. Install the M4 BHCS. See Figure 6. 2. Tighten the screw enough to hold the locator. Make sure the M4 BHCS PIVOT LOCATOR locator can still float freely with hand pressure. Figure 6 3. Insert the proper terminal fully into the correct profile slot until the terminal is fully seated and stops. Then gently pivot the locator closed. 4. With hand pressure, slowly slide the locator to the correct position. See Figure 5. 5. Gently pivot the locator open without disturbing the location. 6. Hold the locator firmly in place and slowly tighten the M4 BHCS. Maintenance It is recommended that each operator of the tool be made aware of, and responsible for, the following maintenance steps: 1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth. 2. Do not use any abrasive materials that could damage the tool. 3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine oil. Do not oil excessively. The tool was engineered for durability but like any other equipment it needs cleaning and lubrication for a maximum service life of trouble free crimping. Light oil (such as 30 weight automotive oil) used at the oil points, every 5,000 crimps or 3 months, will significantly enhance the tool life. 4. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto certain terminations may affect the electrical characteristics of an application. 5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies, and store the tool in a clean, dry area. Miscrimps or Jams Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or closed. The tool will open easily by lifting the ratchet release lever. See Figure 10. Warranty This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30 days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping, fixturing, or use of handle extensions voids this warranty. Doc No: ATS-6382379HM Release Date: 09-02-10 UNCONTROLLED COPY Page 4 of 7 Revision: B Revision Date: 10-14-10

Hand Crimp Tool for 2.50mm Board-In Crimp Terminals CAUTION: Repetitive use of this tool should be avoided. CAUTIONS: 1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for production use. Repetitive use of this tool should be avoided. 2. Insulated rubber handles are not protection against electrical shock. 3. Wear eye protection at all times. 4. Use only the Molex terminals specified for crimping with this tool. Notes: 1. This tool should only be used for the terminals and wire gauges specified on this sheet. 2. This tool is not adjustable for crimp height; however crimp force is adjustable (See instructions above). Variations in tools, terminals, wire stranding, and insulation types may affect crimp height. 3. This tool is intended for standard conductor sizes. It may not give a good insulation crimp support for all insulation sizes. 4. Molex does not repair hand tools (see warranty above). The replacement parts listed are the only parts available for repair. If the handles or crimp tooling is damaged or worn, a new tool must be purchased. 5. Pull force should be used as the final criteria for an acceptable crimp. Pull force is measured with no influence from the insulation crimp. The insulation should be stripped long (1/2 in.) so the insulation grips on the terminal do not grip the wire insulation or the conductor. Refer to Molex Quality Crimping Handbook 63800-0029 for additional information on crimping and crimp testing. 6. Molex does not certify crimp hand tools. CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling. Applications for the Modular Crimp Head WARNING: NEVER operate, service, install, or adjust this Modular Crimp Head without proper instruction and without first reading and understanding the instructions in the proper Manual or Specification Sheet. See Chart below for the correct Manual or Specification Sheet. WARNING: NEVER install tooling or service this tool while it is into any power source. Disconnect the power by unplugging or turn off the Actuator from its power source. CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury. CAUTION: Wear safety glasses when operating or serving this tool. Doc No: ATS-6382379HM Release Date: 09-02-10 UNCONTROLLED COPY Page 5 of 7 Revision: B Revision Date: 10-14-10

Hand Crimp Tool for 2.50mm Board-In Crimp Terminals The chart below shows all applications for this Modular Crimp Head. Modular Crimp Head Tool Tool Adapter Adapter Figure Order No. Order no. Description Order No. Description No. 63816-0000 Hand Crimp Frame (Short) N/A N/A 7 63816-0050 Hand Crimp Frame (Long) N/A N/A 7 63823-7970 63816-0200 Battery Power Tool (110 V) 63816-0600 Battery Power Crimp Adapter 8 63816-0250 Battery Power Tool (220 V) 63816-0600 Battery Power Crimp Adapter 8 63816-0100 Air Power Tool 63816-0700 Air Power Crimp Adapter 9 Applications for the Modular Crimp Head Hand Crimp Tool Battery Powered Tool Air Powered Tool MODULAR CRIMP LOCKING MODULAR MODULAR LOCKING HEAD PINS CRIMP HEAD LOCKING CRIMP PINS PINS HEAD AIR POWER BATTERY CRIMP POWER ADAPTER CRIMP LOCKING PINS ADAPTER AIR LOCKING HAND CRIMP POWER PINS FRAME LONG BATTERY TOOL OR SHORT POWERED TOOL Figure 7 Figure 8 Figure 9 Doc No: ATS-6382379HM Release Date: 09-02-10 UNCONTROLLED COPY Page 6 of 7 Revision: B Revision Date: 10-14-10

Hand Crimp Tool for 2.50mm Board-In Crimp Terminals PARTS LIST Hand Crimp Tool 63823-7900 Item Order Number Description Quantity 1 63823-7970 Modular Crimp Head 1 2 63816-0000 Hand Crimp Frame (Short) 1 3 63823-7975 Locator 1 4 63816-0001 Locking Pin 2 5 63600-0525 Handle Spring 1 6 63600-0520 Crimping Spring 2 5 HANDLE SPRING 2 M4 X 8mm LONG BHCS RATCHET RELEASE LEVER 3 LOCATOR Figure 10 4 1 6 CRIMPING SPRING (2) http://www.molex.com Doc No: ATS-6382379HM Release Date: 09-02-10 UNCONTROLLED COPY Page 7 of 7 Revision: B Revision Date: 10-14-10