LANGUAGE CRIMP SPECIFICATION JAPANESE ENGLISH (cid:2073)(cid:15919)(cid:15916)適用範囲 SCOPE(cid:2074) 本仕様書(cid:2147)(cid:2058) 殿 (cid:2143)納入(cid:2125)(cid:2175) 2.0mm PITCH GRID WIRE TO BOARD CONN. CRIMP TERM (cid:2146)圧着(cid:2143)伴う諸元(cid:2143)ついて規定(cid:2125)(cid:2175)(cid:2059) THIS STANDARD SPECIFIES THE DIMENSIONS AFTER CRIMPING OF THE 2.0mm PITCH GRID WIRE TO BOARD CONNECTOR TERMINAL. (cid:2073)(cid:15920)(cid:15916)適用端子(cid:15917)電線 APPLICABLE TERMINAL(cid:15917)WIRE(cid:2074) 端 子 型 番 適用電線 WIRE SIZE 絶縁被覆外径 INSULATION Part Number AWG ｍｍ(cid:15920) DIAMETER (cid:15923)(cid:15918)(cid:15921)(cid:15927)(cid:15922)(cid:15915)(cid:15926)(cid:15912)(cid:15912)(cid:15912) 撚(cid:2174)線 ＃(cid:15920)(cid:15922)～＃(cid:15921)(cid:15918) 0.049～0.22 φ0.8 - φ1.4 mm (STRAND WIRE) (cid:2073)(cid:15921)(cid:15916)各部(cid:2146)名称 DEFINITION(cid:2074) (cid:1397)シーム SEAM 第1図 FIG.1 (cid:1393) ベン(cid:2235)ア(cid:2229)(cid:2249) BEND UP (cid:2230)イス(cid:2234) TWISTING ロー(cid:2268)ング ROLLING (cid:1396) 芯線突き出し長さ ベン(cid:2235)(cid:2226)ウン EXTRUDED WIRE LENGTH BEND DOWN (cid:1394) ベ(cid:2269)マウス長さ BELL MOUTH (FLARE) (cid:1399) 被覆圧着部高さ INS. CRIMP HEIGHT (cid:1398) 芯C線ON圧D着U部CT高OさR CRIMP HEIGHT (cid:1395) (cid:2205)CU(cid:2229)T(cid:2234)-O(cid:2204)FF(cid:2247) T(cid:2225)AB(cid:2248) L長EさNGTH REV. A SHEET 1-4 REVISE ON PC ONLY TITLE: 2.0mm GRID WIRE TO BOARD CONN. 新規作成 A RELEASED CRIMP TERMINAL 177772 圧着仕様書 06/06/2018 GSHARMA THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC REV. DESCRIPTION TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DESIGN CONTROL STATUS DATE: WRITTEN BY: CHECKED BY: APPROVED BY: J M.YAGI Y.ITO H.IKESUGI 1993/06/09 DOCUMENT NUMBER DOC. TYPE DOC. PART CUSTOMER SHEET CS-50394 PSD 001 GENERAL MARKET 1 OF 4 EN-127(2015-12 )

LANGUAGE CRIMP SPECIFICATION JAPANESE ENGLISH (cid:2073)(cid:15922)(cid:15916)仕様 SPECIFICATION(cid:2074) 番号 項目 ITEM 仕様 REQUIREMENT NUMBER ベン(cid:2235)ア(cid:2229)(cid:2249) BEND UP (cid:15922)°以(cid:2903) / MAX. ベン(cid:2235)(cid:2226)ウン BEND DOWN (cid:15921)°以(cid:2903) / MAX. (cid:1393) (cid:2230)イス(cid:2234) TWISTING (cid:15921)°以(cid:2903) / MAX. ロー(cid:2268)ング ROLLING (cid:15922)°以(cid:2903) / MAX. ベ(cid:2269)マウス(cid:15910)参考値(cid:15911) (cid:1394) (cid:15918).(cid:15918)(cid:15923)～(cid:15918).(cid:15921)(cid:15923)ｍｍ BELL MOUTH (REF.) (cid:2205)(cid:2229)(cid:2234)(cid:2204)(cid:2247)(cid:2225)(cid:2248)長さ (cid:1395) (cid:15918) ～(cid:15918).(cid:15919)(cid:15923) ｍｍ以(cid:2903) / MAX. CUT OFF TAB LENGTH 芯線突き出し長さ (cid:1396) (cid:15918)～(cid:15918).(cid:15923)ｍｍ EXTRUDED WIRE LENGTH シーム(cid:2147)閉(cid:2124)てい(cid:2175)こと(cid:2059)但し開き(cid:2146)あ(cid:2175)場合(cid:2147)芯 シーム 線(cid:2146)飛び出し(cid:2142)きこと(cid:2059) (cid:1397) SEAM SEAM SHALL NOT BE OPENED AND NOT WIRE ALLOWED OUT OF CRIMPING THE AREA. 絶縁被覆むき長さ(cid:15910)参考値(cid:15911) ≠ (cid:15919).(cid:15921)～(cid:15919).(cid:15926)ｍｍ WIRE STRIP LENGTH (REF.) (cid:2073)(cid:15923)(cid:15916)圧着条件(cid:15910)(cid:1398)及び(cid:1399)(cid:15911)CONDITIONS(cid:2074) 電線(UL1007相当品)を圧着した際(cid:2146)要件(cid:2147)(cid:2903)記(cid:2143)よ(cid:2175)(cid:2059) AFTER CRIMPING THE STRAND WIRE (EQUIVALENT TO UL1007), THE CRIMPED AREAS SHOULD BE AS FOLLOWS. (cid:1398)芯線圧着部高さ (cid:1399)被覆圧着部 (cid:2225)ー(cid:2257)(cid:2236)(cid:2269) 圧着 CONDUCTOR CRIMP INSULATION 電線サイ(cid:2220) HEIGHT 圧着部引張強度 番号 WIRE SIZE (cid:2230)ー(cid:2269)番号 工具 工具 CRIMP STRENGTH TERMINAL (AWG) CRIMP DIE マー(cid:2209) 高さ マー(cid:2209) 参考高さ (N {Kgf}) NO. MODEL NO. HEIGHT HEIGHT (REF.) TOOL (mm) TOOL (mm) MARK MARK 0.60 29.4{3.0}以(cid:2902) / ＃(cid:15920)(cid:15922) (*1) C 6 1.35 ～0.65 MIN. 0.59 19.6{2.0}以(cid:2902) / ＃(cid:15920)(cid:15924) C 6 1.35 (cid:15923)(cid:15918)(cid:15921)(cid:15927)(cid:15922) (cid:15923)(cid:15925)(cid:15921)(cid:15919)(cid:15923) ～0.64 MIN. (cid:15915)(cid:15926)(cid:15912)(cid:15912)(cid:15912) (cid:15915)(cid:15921)(cid:15918)(cid:15918)(cid:15918) 0.56 9.8{1.0}以(cid:2902) / ＃(cid:15920)(cid:15926) B 6 1.30 ～0.61 MIN. 0.53 4.9{0.5}以(cid:2902) / ＃(cid:15921)(cid:15918) A 5 1.30 ～0.58 MIN. 注) *1 UL1061相当品を圧着した際(cid:2146)条件 NOTE. AFTER CRIMPING WIRE (EQUIVALENT TO UL1061), THE CRIMPED AREA SHOULD BE AS FOLLOWS. REVISE ON PC ONLY TITLE: 1.25 W/B CONN. A RECEPTACLE CRIMP TERMINAL SEE SHEET 1 OF 4 圧着仕様書 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC REV. DESCRIPTION TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DOCUMENT NUMBER DOC. TYPE DOC. PART CUSTOMER SHEET CS-50394 PSD 001 GENERAL MARKET 2 O F 4 EN-127(2015-12)

LANGUAGE CRIMP SPECIFICATION JAPANESE ENGLISH (cid:2073)6(cid:15916)消耗部品一覧表 PERISHABLE PARTS LIST(cid:2074) 部品名称 PART NAME 部品番号 PART NO. アンビ(cid:2269) ANVIL 57175-2101 芯線(cid:2209)(cid:2268)ン(cid:2249)パン(cid:2227) COND. PUNCH 57175-2102 被覆(cid:2209)(cid:2268)ン(cid:2249)パン(cid:2227) INS. PUNCH 57175-2103 (cid:2247)ロン(cid:2234)(cid:2247)ローテ(cid:2197)ングシ(cid:2201)ア FRONT FLOATING SHEAR 57067-2006 (cid:2247)ロン(cid:2234)ホ(cid:2269)(cid:2226)ー FRONT HOLDER 57067-2005 REVISE ON PC ONLY TITLE: 1.25 W/B CONN. A RECEPTACLE CRIMP TERMINAL SEE SHEET 1 OF 4 圧着仕様書 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC REV. DESCRIPTION TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DOCUMENT NUMBER DOC. TYPE DOC. PART CUSTOMER SHEET CS-50394 PSD 001 GENERAL MARKET 3 O F 4 EN-127(2015-12)

LANGUAGE CRIMP SPECIFICATION JAPANESE ENGLISH REV. REV. RECORD DATE EC NO. WRITTEN BY : CHECKED BY : 0 RELEASED 09/06/93 T30267 M.YAGI -- REDRAWN & D 06/06/18 177772 G.SHARMA A.TEZUKA RELEASED REVISE ON PC ONLY TITLE: 1.25 W/B CONN. A RECEPTACLE CRIMP TERMINAL SEE SHEET 1 OF 4 圧着仕様書 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC REV. DESCRIPTION TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DOCUMENT NUMBER DOC. TYPE DOC. PART CUSTOMER SHEET CS-50394 PSD 001 GENERAL MARKET 4 O F 4 EN-127(2015-12)

9 8 7 6 5 4 3 2 1 ENG. P/NS CONTACT PLATING FORM : LOOSE FORM : CHAIN (NICKEL OVERALL 2-6 µm MIN) 50394-8100 50394-8051 0.38µm GOLD MIN. 50394-8200 50394-8052 0.76µm GOLD MIN. 50394-8400 50394-8054 GOLD FLASH 0.05 - 0.125µm E E 50394-8500 50394-8055 2.50µm MATTE TIN MIN. A B �0.2� 1.40 B A 1.88 0.2�CUT-OFF TAB LENGTH� 1.23 D D 2.00 1.33 SECTION B-B SECTION A-A 6.25±0.30 C C 2.90 �3.35� 2.35 0.65 0.80 1.74 NOTES : 1. MATERIAL: COPPER ALLOY 2. APPLICABLE HOUSING : 51110-***1 B B : 51110-**5* : 151100-00** �3.80� �CONTACT PLATING AREA�0.95MIN 3. APPLICABLE WIRE: AWG #24-#30 WIRE INSULATION OD: 1.40mm MAX. 4. CRIMPING SPECIFICATION: CS-50394 WINDING DIRECTION QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SYMBOLS 17 08 19 DIMENSION UNITS SCALE VIEW Z = 0 6/08/ 7/05/ 7/05/ GE(UNNELREASLS T SOPLEECRIAFINECDE)S MM NTS 1 1 1 0 0 0 = 0 CTR 2 2 2 MM INCH DRWN BY DATE N E 4 PLACES ± ± S.Q 1994/04/20 SALES DRAWING = 0 ED I 3 PLACES ± ± CHK'D BY DATE 2.0MM GRID W TO B CONN. CRIMP TERMINAL R A = 0 E Y 2 PLACES ± 0.2 ± EDPOH 1994/04/27 A TO T L S R ASSEMBLY VIEW Z == 00 RE-MA 116436 MUM GMENA KHLIM10 PPLLAACCEESS ±± ±± ALPBPRL BEYE DATE 2013/11/13 SERIES MA TPERRIAOL NDUUMBCERT CUSTOMER CDUSRTOAMWERING NO: WN: K'D: PR: ANGULAR TOL ± 3.0 DRAWING SIZE THIRD ANGLE PROJECTION 50394 SEE TABLE GENERAL MARKET = 0 C R H P E D C A DRAFT WHERE APPLICABLE MUST REMAIN A3 DOCUMENT NUMBER DOC TYPE DOC PART SHEET NUMBER RELEASE STATUS RELEASE DATE C = 0 C REV WITHIN DIMENSIONS SD-50394-8XXX PSD 000 1 OF 1 FROERVIMSAIOTN: M: Cet-lega-master-tb-prod-A39 8 7 6 5 4 3 2 1 DATE: 2016/02/04